THE ART OF BASIC PLUMBING FOR INSTALLING A BATHTUB

The Art of Basic Plumbing for Installing a Bathtub

The Art of Basic Plumbing for Installing a Bathtub

Blog Article

View More

This article which follows on the subject of How to Install a Bathtub is fairly remarkable. Check it out for your own benefit and decide what you think of it.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bathtub isn't exactly brain surgery, but it does require solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard task. If the old tub is conveniently accessible, the task can move immediately; if you need to open up a wall to remove the old tub and position the brand-new tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the work and also fit trying it. Instead of employing a professional to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have actually already bought a new tub and also don't require to change the arrangement of your previous water pipelines.
Your devices and product list should comprise the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be rather troublesome as a result of the restricted accessibility that is often the situation.
    Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipes. When the supply pipes have been gotten rid of, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
    Prior to going on to fit the new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the current supply pipes.
    If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in location in between the faucet and also the sink. Safeguard the faucet in place with the maker provided backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The previous type should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

    Mounting the Bath tub


    Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
    The following objective is to make sure that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub until the spirit level reads degree.
    To install taps, fit the bottom of the outermost versatile faucet port to the suitable supply pipe by making a compression sign up with; then do the exact same for the other tap.
    Turn on the water as well as inspect all joints and also new pipework for leakages as well as tighten them if necessary. Load the bath tub and additionally inspect the overflow outlet as well as the typical outlet for leaks.
    Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling and securing around the bath tub needs to wait till the tub has been made use of at the very least when as this will certainly settle it into its last position.

    Preparing for the Installation


    Firstly, the supporting frame supplied with the bathroom should be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
    Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize all of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final setting.

    Tiling Around the Tub


    In the area where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, leading to problems with moisture and also possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the motion experienced when the bathtub remains in use. The sealant can break fairly very early if you do not think about this motion prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    As an enthusiastic person who reads on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that piece was essential. Enjoyed reading our blog entry? Please share it. Let another person find it. Thanks a bunch for your time. Visit us again soon.


    Book An Estimate Now

    Report this page